Classic Bond EPDM membrane is suitable for installation on a vast range of roofing projects, install the sure each gutter trim back plate to the fascia at the gutter edge. This is available in two variations as a standard trim to be installed onto a 50 millimeter by 25. Millimeter timber batten or as a baton back plate, as shown here that is installed directly to the face of the fascia. This option replaces the timber entirely with a deeper PVC back plate use the provided stainless steel ring shank nails allow an expansion gap of one millimeter per meter of run between lengths of Shur edge PVC trim if using WBA as the deck adhesive mark 100 millimeters around The roof perimeter as a guide to transfer from WBA to the perimeter band of bonding adhesive if using bonding adhesive as the deck adhesive. This is not required in this instance.
The roof can be done in one piece, and this is typical of many freestanding buildings such as garages. The membrane should be laid out allowing it to overhang the edges of the building 75 millimeters all round is normal, but this can be adjusted to suit site requirements. Allow the membrane to relax prior to bonding to the deck typically half an hour is sufficient, but this will vary depending on the ambient conditions, when the membrane has been given adequate time to relax, draw it back to the center point and apply the water-based adhesive to The deck for non-timber deck surfaces this should be carried out using the bonding adhesive, which is applied to both the deck and the underside of the membrane. Do not allow WBA adhesive to tack off, lay the membrane into the adhesive while it is still wet. The adhesive must transfer to the underside of the membrane.
This can be carried out in stages if required, to ensure this is achieved. Many classic Bond membranes have a dusting of talc to make installation and handling easier once the membrane has been laid into the adhesive. It can be broomed into position to remove any air and ensure positive contact to the adhesive beneath once this has been completed. It can be repeated for the opposite side of the roof. Draw the membrane back to the center point again apply the adhesive to the deck area and lay in the membrane as before.
If using WBA, the next stage is to apply the bonding adhesive to the roof perimeter that has been kept free from WBA by working on opposite sides of the roof. You are able to ensure the work is carried out with maximum efficiency and complete projects quickly. Bonding adhesive must be applied to both the deck and the underside of the membrane. Bonding adhesive must be allowed to tack off before the surfaces are put together. This allows solvents to escape and ensures it does not cause the membrane to blister if blistering does occur.
As a result of this, it is likely to be temporary you when the membrane installation is complete. The Shore edge PVC trims can be fixed into position. These finish the roof neatly and provide additional secure montfort membrane at the roof perimeter. The shore edge gutter trim front plate is nailed into position using the supplied, poly top nails through the pre-drilled fixing holes. This provides the Installer with preset centers for the fixings and ensures the gutter edge is fixed securely and neatly.
The pre applied foam strip forms a watertight seal under compression and ensures water flows over the top of the trim trim off the excess membrane from the gutter edge. If stapling, the membrane at the corners ensure the staples are always weathered prior to installing the Shore edge, check, curb sure edge check, curbs can be installed to any edge where there is no gutter. The membrane should be trimmed back, allowing a minimum of 50 millimetres overhanging. The roof edge by compressing the pre applied foam strip between 30 and 50 percent. A watertight seal is achieved as with the gutter trim, these are nailed into position using the supplied, poly top nails through the pre-drilled fixing holes all Shore edge.
Pvc trims require an expansion gap of one millimeter per meter of run between lengths of trim. The final step to complete the roof is to attach the corners and joining cliffs. A plastic adhesive applied to one side, accommodates any movement and is used to complete this for projects in excess of 100 square metres. Reinforced Universal securement strip commonly called rusts should be applied to every roof perimeter and bonding adhesive used for the deck adhesive. Please consult your distributor for more information on larger scale installations.
You
Read More: How to Paint a Room | Painting Tips | The Home Depot
